Study Guide: Approach

the role of Approach Controllers

TMA Controllers (S3) includes approach and departure control services associated with a particular airport.

• maintain an orderly flow of traffic
  
• provide a separation service between aircraft
  
• provide assistance to pilots
  

The greatest difference when you are starting you TMA-carreer will be the separation between approaching and departing traffic.
There are some separation in your airspace:

• Vertical separation: should be at least RVSM 1000ft, Non-RVSM 2000ft. Austria uses RVSM (Reduced Vertical Seperation Minima). So you can use 1000ft up to FL410.
  
• Horizonal separation: The Minimum Horizontal Seperation depends on the radar equipment involved. APP Sectors work with a minimum of 3 nm, CTR Sectors use 5 nm.
  

How to maintain visual separation?
You may use:

• Lateral vectoring When issuing a heading to an aircraft, make sure that you are using a direction ending on 0 (zero) or on 5 (five).
• Vertical vectoring: climbing or descending. For departing or arriving traffic you also can use a "stop climbing/descending at FLxxx" to avoid a conflict.
  
• Speed limit: A controller may issue speed instructions within an aircrafts operating limits. There are two possible ways to do this, either by using Indicated Airspeed (FL280 or below) or by specifying a Mach number (FL280 or above). Take notice of the minimum speed of the aircraft! Normally you are working with "minimum clean" (means the lowest speed an aircraft can maintain without using flaps or spoilers) above FL100. The second is “minimum approach speed” which is the lowest speed an aircraft can maintain using both flaps and spoilers.
  

Phraseology

A ...Pilot
G...ATC

Approach

Standard clearances for arriving aircraft shall contain the following items, if applicable:

1. Aircraft identification
2. Designator of assigned STAR
3. Runway-in-use, except when part of the STAR description
4. Initial level, except when this element is included in the START description and
5. Any other necessary instructions or information not contained in the START description, e.g. change of communication

Type of approach procedure

G: CLEARED / PROCEED VIA (designator) ARRIVAL
G: CLEARED TO (clearance limit) VIA (designator) ARRIVAL
G: CLEARED (type of approach) APPROACH RUNWAY (number)
G: CLEARED LOCALIZER APPROACH [RUNWAY (number)] [GLIDE PATH INOPERATIVE]
G: CLEARED APPROACH RUNWAY (number)
A: REQUEST (type of approach) APPROACH [RUNWAY (number)]
G: (type of approach) NOT AVAILABLE DUE (reason) [alternative instructions]
A: REQUEST (RNAV plain language designator)
G: CLEARED (RNAV plain language designator)
G: ARE YOU FAMILIAR WITH (name) APPROACH PROCEDURE [RUNWAY (number)]?

Straight-in approach

A: REQUEST STRAIGHT-IN / DIRECT [type of approach] APPROACH [RUNWAY (number)]
G: CLEARED STRAIGHT-IN / DIRECT [type of approach] APPROACH [RUNWAY (number)]

Approach instructions with radar

G: VECTORING FOR (tpye of pilot interpreted aid) APPROACH RUNWAY (number)
G: VETORING FOR VISUAL APPROACH RUNWAY (number), REPORT FIELD / RUNWAY IN SIGHT
G: VECTORING FOR (positioning in the circuit)
G: VECTORING FOR SURVEILLANCE RADAR APPROACH RUNWAY (number)
G: VECTORING FOR PRECISION APPROACH RUNWAY (number)
G: (type) APPROACH NOT AVAILABLE DUE (reason) (alternative instructions)
G: POSITION (number) MILES FROM (position) / TOUCH DOWN. TURN LEFT / RIGHT HEADING (three digits)
G: YOU WILL INTERCEPT (radio aid or track) (distance) FROM (significant point) / TOUCH DOWN
A: REQUEST (distance) FINAL
G: CLEARED FOR (type) APPROCH RUNWAY (number)
G: REPORT ESABLISHED [ON ILS / LOCALIZER / GLIDE PATH]
G: REPORT ESTABLISHED ON FINAL APPROACH TRACK
G: CLOSING FROM LEFT / RIGHT [REPORT ESTABLISHED]
G: TURN LEFT / RIGHT HEADING (three digits) [TO INTERCEPT [RIGHT TO LEFT / LEFT TO RIGHT / REPORT ESTABLISHED]
G: EXPECT VECTORS ACROSS (localizer or radio aid) (reason)
G: THIS TURN WILL TAKE YOU THROUGH (localizer or radio aid) [reason]
G: TAKING YOU THROUGH (localizer or radio aid) [reason]
G: MAINTAIN (altitude) UNTIL GLIDE PATH INTERCEPTION
G: REPORT ESTABLISHED ON GLIDE PATH
G: INTERCEPT (localizer or radio aid) [REPORT ESTABLISHED]
G: INTERCEPT (radio aid) [LEFT TO RIGHT / RIGHT TO LEFT]
G: CLEARED FOR ILS APPROACH RUNWAY (number) LEFT / RIGHT
G: YOU HAVE CROSSED THE LOCALIZER. TURN LEFT / RIGHT IMMEDIATELY AND RETURN TO THE LOCALIZER
G: ILS RUNWAY (number) LEFT / RIGHT LOCALIZER FREQUENCY IS (number)
G: TURN LEFT / RIGHT (number) DEGREES / HEADING (three digits) IMMEDIATELY TO AVOID TRAFFIC [DEVIATING FROM ADJACENT APPROACH], CLIMB TO (level)
G: CLIMB TO (level) IMMEDIATELY TO AVOID TRAFFIC [DEVIATING FROM ADJACENT APPORACH] (further instructions)

Go around

G: GO AROUND IMMEDIATELY (missed approach instruction) (reason)
G: IF GOING AROUND (appropriate instructions)
G: ARE YOU GOING AROUND?
A: GOING AROUND

Level changes, reports and rates

G: CLIMB / DESCEND
- TO (level)
- TO AND MAINTAIN BLOCK (level) TO (level)
- TO REACH (level) AT / BY (time or significant point)
- REPORT LEAVING / REACHING / PASSING (level)
- AT (number) FEET PER MINUTE [OR GREATER / LESS]
G: REQUEST LEVEL / FLIGHT LEVEL / ALTITUDE CHANGE FROM (name of level) [AT (time or significant point)]
G: STOP CLIMB / DESCENT AT (level)
G: CONTINUE CLIMB / DESCENT TO (level)
G: EXPEDITE CLIMB / DESCEND [UNTIL PASSING (level)]
G: RESUME NORMAL RATE OF CLIMB / DESCENT
G: REPORT LEAVING / REACHING / PASSING (level)
G: WHEN READY CLIMB / DESCENT TO (level)
G: EXPEDITE CLIMB / DESCENT AT (time of significant point)
G: EXPEDITE CLIMB / DESCENT UNTIL PASSING (level)
A: REQUEST DESCENT AT (time)
A: REQUEST ALTITUDE (number FEET) / FLIGHT LEVEL (number) VIA (route) [DUE TO (reason)]
A: REQUEST LEVEL CHANGE / CLIMB / DESCENT AT (time / position)
G: EXPECT LEVEL CHANGE / CLIMB / DESCENT
- FROM (name of unit)
- AT (time or position)
- AFTER PASSING (position)
- IN (number) MINUTES
G: IMMEDIATELY
G: AFTER PASSING (significant point)
G: AT (time or significant point)
G: WHEN READY (instructions)

Vectoring

G. LEAVE (significant point) HEADING (three digits) [INBOUND [AT (time)]
G: CONTINUE HEADING (three digits)
G: CONTINUE PRESENT HEADING
G: FLY HEADING (three digits)
G: TURN LEFT / RIGHT HEADING (three digits) [reason]
G: TURN LEFT / RIGHT (number) DEGREES [reason]
G: STOP TURN HEADING (three digits)
G: FLY HEADING (three digits), WHEN ABLE PROCEED DIRECT (name) (significant point)
G: HEADING IS GOOD
G: WHEN ABLE PROCEED DIRECT (position)
G: SUGGEST (suggestion)
G: IF UNABLE [(alternative instructions)] ADVISE
A: UNABLE TO COMPLY (reason)
G: VECTORING FOR SPACING / SEPERATION / DELAY
G: VECTORING DUE TO TRAFFIC
G: RESUME OWN NAVIGATION (position of a/c) (specific instructions)
G: RESUME OWN NAVIGATION [DIRECT] (significant point) [MAGNETIC TRACK (three digits) DISTANCE (number) MILES]
G: MAKE A THREE SIXTY TURN LEFT / RIGHT [reason]
G: ORBIT LEFT / RIGHT [reason]
G: MAKE ALL TURNS RATE ONE / RATE HALF (number) DEGREES PER SECOND START AND STOP ALL TURNS ON THE COMMAND “NOW”
G: ALL TURNS RATE ONE / RATE HALF (number) DEGREES PER SECOND, EXECUTE ISNTRUCTIONS IMMEDIATELY UPON RECEIPT
G: TURN LEFT / RIGHT NOW
G: STOP TURN NOW

Speed instructions:

G: REPORT SPEED
G: REPORT INDICATED AIRSPEED / TRUE AIRSPEED / MACH NUMBER
A: SPEED (number) KNOTS / MACH (number)
G: MAINTAIN (number) KNOTS / MACH (number) [OR GREATER / LESS] [UNTIL (significant point)]
G: DO NOT EXCEED (number) KNOTS / MACH (number)
G: MAINTAIN PRESENT SPEED
G: INCREASE / REDUCE SPEED (number) KNOTS / MACH (number) [OR GREATER / LESS]
G: INCREASE / REDUCE SPEED BY (number) KNOTS / MACH (number) [OR GREATER / LESS]
A: UNABLE TO COMPLY, INDICATED AIRSPEED WILL BE (number) KNOTS / MACH (number)
G: RESUME NORMAL SPEED
G: REDUCE TO MINIMUM APPROACH SPEED
G: REDUCE TO MINIMUM CLEAN SPEED
G: REDUCE TO MINUMUM SPEED
A: MINUMUM SPEED / MINIMUM CLEAN SPEED / MINIMUM APPROACH SPEED IS (number) KNOTS
G: NO [ATC] SPEED RESTRICTIONS

Flight rules

A: CANCELLING IFR
G: IFR CANCELLED AT (time)

A: REQUEST IFR CLEARANCE
G: CLEARED TO (clearance limit), VIA (route) (level) (other instructions), IFR [FLIGHT] STARTS AT (position or time) / WHEN REACHING (level) / PASSING (level) / NOW [(instructions)]

G: CLEARED NIGHT VFR
G: CLEARED SPECIAL VFR

FAQs

How do I work with STARs and Transitions?
STAR means Standard Instrument Arrival is like a route to the airport.This road has a name that has three parts. The first part is the navigational point where the route starts, the second is the version number, and the third is usually but again not always coupled to a certain runway(s). Transitions are connecting between the end of STAR to the final.
Using STARs and Transition simplifies the arrival considerably for both pilots and controllers. By clearing "transition and profile" the pilot has also the clearance for descending as published. So you can expect the track, descend and speed of an aircraft.

How to use a Holding?
The primary use of a holding is delaying aircraft that have arrived over their destination but cannot land yet because of traffic congestion, poor weather, or unavailability of the runway. Several aircraft may fly the same holding pattern at the same time, separated vertically by 1,000 feet or more.
A holding is situated around a holding fix. In a standard holding pattern the aircraft flies inbound to the holding fix on a certain course (Inbound leg). After passing the fix it turns right (standard turn: 2° per second) and flies one minute (1,5 min above FL 140) into the other direction (outbound leg). After one minute the pilot turns right again (standard turn) and establishes again on the inbound leg.
If you count all this together you end up with four minutes required to finish one holding pattern. However some holding patterns use left turns, others don't use one minute to measure the outbound leg, but fly to a certain distance.
Also every holding has a minimum altitude.

What does MRVA mean?
Minimum Radar Vectoring Altitude: lowest altitude above MSL that can be used for IFR vectoring

When is the best moment for my handoff?
Out of conflict and as early as possible.

Which classes of airspace are provided in Austria?

• C (Charlie) controlled airspace, IFR and VFR possible, aircontroll is mandatory. IFR will be separated to other IFR and VFR traffic, VFR traffic receive traffic information about other VFR traffic. C starts AT FL195 and inside Special Rules Area (e.g. SRA Wien)
  
• D (Delta) controlled airspace, IFR and VFR possible, aircontroll is mandatory. IFR is separated to other IFR and receives traffic information about other VFR; VFR traffic reveives information about other traffic. D in Austria covers space between FL125 and FL195 (CTA) and inside contolled zones and certain SRA.
• E (Echo) controlled airspace only for IFR; VFR receives information as far as possible. In Austria up to FL125 in inside of certain TCAs (Terminal Control Areas).
• G (Golf) uncontrolled airspace. Traffic information as far as possible.
  
  

What are Y and Z-flights?
Basically these are flights with a change between IFR/VFR

• Y starts with IFR, changing to VFR (IFR cancellation)

• Z starts with VFR, changing to IFR (IFR pickup)

References

Information about airspaces and airways can be found here: [1]

Details about air pressure and altitudes you will find here: [2]

Local Procedures

LOWW

Frequencies:

LOWW_APP can be divided into up to six Sectors:

LOWW_APP	LOWW_N_APP	LOWW_S_APP	LOWW_F_APP	LOWW_D_APP	LOWW_DEP
128.200	124.550	129.550	119.800	132.470	118.770
GND-FL105	FL105-FL245	FL105-FL245	1st Director	2nd Director	Departure

The decision which sectors are used shall be based on traffic Situation.

Transition Altitude: 5000ft

Limits

- vertikal: GND - FL245 - lateral: see appendix and shown by sectorfile

Arrivals

• LOVV_CTR should clear traffic for LOWW STAR. Hand-off 2 minutes before listed waypoints below:

VIA	FL
MASUR	at FL170
BARUG	at FL170
NIGSI	at FL180

• LHCC: approaching traffic is maintaining FL140 over GIGOR

• LZBB: arriving traffic via TOKVA has to maintain FL160 and via REKLU FL180

• LKAA: FL 130 via MIKOV/LEDVA and FL170 via LANUX FL170

Departures

• via UMBIL, OSPEN, SITNI, LUGIM and MOTIX cleared to FL200.

Those flights are released to LOVV_CTR for further climb within the Release Area South and Release Area West (see Appendix)

• via LANUX, KOVEL, MIKOV, LEDVA cleared FL240 to LKAA_CTR.

• via SASAL, STEIN cleared FL230 to LHCC_CTR

• via ABLOM cleared FL150 (ABLOM FL130 or above) to LZBB_CTR.

• LOWW to LOWL: maximum FL160 (hand-off to LOWL_APP)

• LOWW to LOWG: maximum FL160 (hand-off to LOWG_APP)

• LOWW to LOWS / LOWK / LOWI: if requested FL is above FL160, traffic shall be transferred to LOVV_CTR.

Inbound / Outbound LZIB (Bratislava) and LKTB (Brno)

• Inbounds LKTB and LZIB shall be cleared from LOVV_CTR to FL210 and hand-off short before Approach Area Wien.

• Outbounds LKTB and LZIB shall be cleared to FL240 and hand-off to LOVV_CTR.

inbound LZIB	FL070 (KUNET at level)
outbound LZIB	climbing FL120
inbound LKTB	FL110 (MIKOV at level)
outbound LKTB	climbing FL100
LOWW to LZIB	FL070 (ABLOM at level)
LZIB to LOWW	6000ft (TOVKA at level)

Remarks

• Coordination regarding procedures not listed in this document shall be done in due time with the respective and responsible ATC unit.

• LOWW_APP may send departing traffic to the last waypoint of the SID without coordination.

• Hand-off for arrivals to LZIB short before MIRLU.

Appendix

LOWI

Frequencies: 119.27

Transition Altitude: 11000ft

Limits

- vertikal: GND - FL165

Arrivals

• LOC/DME West via KTI FL130 over KTI

• LOC//DME East via RTT 9500ft over RTT

• RNP – RNAV Approach Runway 26: instrumental approach with lower minimas, final also a visual approach. Only on pilot request; different miss-appproach-procedure

• All arrivals are going via AB, finals after AB are always visual

The reference sheet you find: downloads.vacc-austria.org/Documents/QRS_LOWI_v1.2.pdf

LOWG

Frequencies: 119.3

Transition Altitude: 4000ft

Limits

- vertikal: GND - FL165

Arrivals There are no STARs in LOWG. Most of the arrival routes ends at GRZ-VOR. After GRAZ normally vectors are used.

• ILS 35C starts at 3300ft. Best way is to intercept at LENIZ at 3500ft.

• VOR-DME 35C: Approach über GRZ-VOR nach DME 7.0 GRZ (heading 147°), danach vector auf final track

• VOR-DME 17C: Approach über GRZ-VOR, starts at D15. GRZ 7000ft, descend profile see chart.

hand/over

• LHCC_CTR via GOTAR FL150

• LJLA_CTR via RADLY FL160

• LOVV_CTR FL160

LOWK

Frequencies: 126.825

Transition Altitude: 7000ft

Limits

- vertikal: GND - FL165

Arrivals

• ILS 28

• NDB-DME 28

• NDB-DME 10

• Circling 10: Anflug über ILS28, desc. 3000ft, circeling starts at KI

hand/over

• LJLA_CTR via REKTI FL160

• LOVV_CTR FL160