Holding Management

Holding managementFrom VACC Austria DokuWiki - TEST Jump to: navigation, search Holding management is an essential part of providing professional ATC - not only but especially in high traffic situations. This tutorial shows what to keep in mind regarding holdings and includes basics of holdings and advanced holding management.

Contents [hide] 1 Definition 2 Standard Holding Pattern 3 ATC Holding Clearances 4 Altitudes And Speed Restrictions 5 Holding Stack And Separation 6 References

Definition A holding (or holding pattern or hold) is a maneuver designated to delay airplanes in flight by keeping them within a specified airspace. Standard holding patterns use right turns, non-standard ones use left turns. Holding patterns may be published on charts (enroute, STARs, approach) or may be given by ATC. Holdings may be anchored on a VOR, VOR/DME, NDB or compass locator, intersection or DME distances.

Standard Holding Pattern A standard holding pattern consists of:

The holding fix A right 180° turn at standard rate (3 degrees/sec) away from the holding fix An outbound leg (standard length: 1 minute below 14000 ft, see below for speed/altitudes) A right 180° turn at standard rate towards the holding fix An inbound leg (standard length: 1 minute) However, pilots have to correct wind shifts, and therefore there is hardly any "ideal" standard pattern.

A standard holding pattern

ATC Holding Clearances A typical ATC holding clearance for a published holding could be: "AUA123, enter holding at NERDU as published, maintain FL90, (220 knots), 1 minute leg, expect further clearance at 1015Z."

Of course, there are times when an ATC - for any reason - can't clear a published holding. Possible holding fixes can be any waypoints, VORs or NDBs, also DME distances or the current position. Anyway, as it is a non-published holding, ATC has to give more information so that pilots know how to fly the holding - for example: "AUA123, proceed direct and hold at NIGSI, FL110, 2 minutes leg, left orbit, expect further clearance at 1310Z."

For longer holdings keep in mind that the pilot has to crosscheck the EFC-time (expect further clearance-time) with available fuel (reserves). Note: the EFC-time is always assigned in the USA (FAA procedures), however in most parts of Europe and also in South America ATC never gives EFC-time, especially for shorter holdings (10-20 minutes). However, advising an EFC-time - if possible - is always a service for the pilot and should be done.

ATC has to issue further instructions while the airplane is in the hold if:

The delay exceeds one hour A revised EFC is necessary Weather is becoming less than the required for the intended approach Other operational information is necessary (eg: airport closed)

Altitudes And Speed Restrictions ICAO holding restrictions Altitude segment for holding Speed (IAS/Mach) in the holding Time length of legs surface to 14,000 ft max. 230 kts 1 minute 14,001 to 20,000 ft max. 240 kts 1 1/2 minutes 20,001 to 34,000 ft max. 265 kts 1 1/2 minutes above 34,001 ft max. 0,83 Mach 1 1/2 minutes

Every published holding has got a minimum holding altitude (MHA) which is noted on the charts. For example, NERDU has an MHA of 5,000 ft (see STAR chart for LOWW here: [1]).

Note that, for operational requirements (e.g. if an extended period of holding is foreseen, to avoid too many “rounds” for passenger comfort or to stay in clean configuration), the pilot may request and ATC grant (if possible), either longer legs (usually 2 minutes) or higher speeds in the holding pattern.

Holding Stack And Separation In periods of very high traffic it may be required that two or more aircraft hold above the same fix. In this case ATC must consider:

Approach sequence shall be kept unchanged. The aircraft that enters the holding at first, should leave it at first too. Aircraft must be separated 1000 feet vertically. Aircrafts may be advised to descend in the holding if necessary for succeeding approach. An aircraft may be cleared to a level previously occupied by another aircraft only after the latter has reported vacating it, except when:

severe turbulence is known to exist; the higher aircraft is effecting a cruise climb; or the difference in aircraft performance is such that less than the applicable separation minimum may result; in which case such clearance shall be withheld until the aircraft vacating the level has reported at or passing another level separated by the required minimum. When the aircraft concerned are established in the same holding pattern, consideration shall be given to aircraft descending at markedly different rates and, if necessary, additional measures such as specifying a maximum descent rate for the higher aircraft and a minimum descent rate for the lower aircraft, should be applied to ensure that the required separation is maintained.

Radar separation shall not be applied between aircraft holding over the same holding point!

References United Virtual Airlines Trainings Departement: Pilot's Guide. Holdings (http://www.united-virtual.com/files/documents/UVA_Guides_HOLDING.pdf)

IVAO: Minimum Radar Vectoring Altitude (MRVA) (http://academy.ivao.aero/node/418)

Retrieved from "http://wikitest.vacc-austria.org/index.php?title=Holding_management"Personal tools Log inNamespaces PageDiscussionVariantsViews ReadView sourceView historyActions Search

Navigation

Main PageImportantATIS templatesStudy GuideAirportsVienna (LOWW)Innsbruck (LOWI)Salzburg (LOWS)Klagenfurt (LOWK)Graz (LOWG)Linz (LOWL) Letter of AgreementsCzech Rep.HungaryGermany (Munich) LinksVACC HomepageVACC Forum Print/exportCreate a bookDownload as PDFPrintable version ToolboxWhat links hereRelated changesSpecial pagesPermanent linkThis page was last modified on 13 April 2012, at 16:27. This page has been accessed 24 times. Privacy policyAbout VACC Austria DokuWiki - TESTDisclaimers